 |
||||||||||||||||
A waste-to-energy technology that eliminates the non-work producing portion of your electricity, resulting in lower electric bills, higher performance and longer life for electric motors and other magnetically driven AC electrical equipment. Without operating power reductions or loss of RPM the Easiliner™ recycles wasted reactive current, generating enough savings to pay for itself 10-15 times over during its normal lifespan, as well as greatly improving the operating efficiency of the treated load. By reducing heat losses and improving voltages in both the electrical supply circuit and the treated load, the Easiliner™ decreases all associated costs - maintenance, repair and replacement, loss of production due to failure, and actual billed electricity costs. [top]
EASI's CompuLiner™ is the state of the art power electronics
cost reduction solution for today's harmonics rich commercial
and industrial facilities. Available in correction ratings of 50, 100, and 300 amperes, the CompuLiner™ line of power correction systems is today's most sophisticated and effective energy cost solution for distortion and reactive current rich environments. The CompuLiner™ is an advanced solution for the complex problem of harmonic distortion current and reactive current in three phase AC power systems. You need not have any reservations about your harmonic and power factor solutions again. You can start reaping the benefits of uninterrupted plant operations, and dramatically reduced electricity billing and equipment maintenance costs now, with CompuLiner™. CompuLiner™ is field selectable for three modes of operation: Harmonic current correction only Reactive current correction only Harmonic and reactive current correction simultaneously The key to CompuLiner's effectiveness is in its ability to
dynamically adjust to the varying load demands of many different
types and configurations of equipment, in real time. By constantly
adjusting its amount and type of correction, and eliminating
the distortion or reactive current being drawn by a treated
load, CompuLiner™ reduces the net current being pulled
through a building's internal distribution system, as well
as through the building's service entrance and revenue meter.
This saves you money in direct billed electricity costs, as
well as on the "indirect" costs of maintenance,
repair, and replacement of sensitive equipment, and on the
costs associated with production downtime due to catastrophic
equipment failure. [top] As most voltage dips are usually less than one second in duration, most industrial facilities and plants are able to ride through such power dips by virtue of their electrical and mechanical inertia. However, contactors, relays, PLC's and starters which control the motors and machinery drop out after only a few milliseconds, resulting in process disruption. Why bother with large, expensive systems to protect the entire facility, such as common battery UPS systems or ferroresonant transformers (CVT's), when the StabiLiner™ provides reliable, maintenance-free AC control power to critical loads in switchboards, motor control centers and other sensitive equipment? No batteries; therefore, no replacement and maintenance costs or hazardous waste. More reliable; ultra-fast (<600 S), off-line system develops little heat & fails to safety. Able to withstand high inrush currents; no need to oversize as with UPS's & CVT's. Lightweight, small & easy to retrofit; no step-up transformers or batteries. Accurate application control; adjustable ride-through time & variable transfer level. Well suited to inductive and low power factor loads. All units are produced to ISO 9000, conform to various industry standards and carry a 3 year warranty. A direct exchange service is available should a unit be faulty or require adjustment and a money-back guarantee is available for new installations to ensure suitability. Power generation, plastics, glass, chemical and food processing, mining, construction, chip fabrication are among the many applications. It can also be used to support adjustable speed drives. [top] Harmonic Correction for Lighting Save even more money with your "high efficiency" lighting systems! Today's electronic ballast fluorescent and HID lighting systems are inherently more cost efficient than their magnetic ballast predecessors. However, one price for this operating efficiency that is becoming more apparent is the high levels of harmonic current drawn by these loads. The disruptions and costs associated with harmonic current are well known, and EASI has introduced the HarmoniLUX 20™ harmonic correction system as the cure for these costs with your electronic fluorescent and HID lighting circuits. The HarmoniLUX 20™ is an accurately designed 3rd order harmonic shunt filter built specifically for 20 ampere lighting circuits in 100 volt to 277 volt systems at either 50 Hz or 60 Hz. By supplying the undesirable 3rd order current frequencies at the breaker, and keeping this current isolated to the individual lighting circuits, your entire facility is protected from the direct operations effects of circulating harmonics, your neutrals are relieved of this harmful loading, your transformers are isolated and run cooler. And, most importantly, the billing costs for your lighting plummet by from 16% to 24%, or more, with absolutely zero loss of luminance. [top] Active Lighting Controller The IllumiLiner™ unit is entirely solid-state with microprocessors
that continually monitor and modify the AC sine wave. The
IllumiLiner™ controls entire circuits of lighting from
the lighting panel, providing circuit-by-circuit flexibility
and a very high rate of return on investment. The well ventilated
cabinet is made of sturdy, heavy gauge metal with a mar-resistant,
epoxy finish to withstand even brutal industrial environments.
Being a superior alternative to "de-lamping" in
order to save energy, the IllumiLiner™ improves the lighting's
performance to voltage, and provides for controllable distribution
of illumination. The IllumiLiner™ automatically adjusts itself to your lighting system voltage. The units are configured at installation for the type of lighting being treated, and then provide exactly the real time correction appropriate for magnetic or electronic ballast fluorescent fixtures; metal halide, sodium, or mercury vapor high intensity discharge fixtures; or incandescent or quartz lighting systems. [top] Advanced Polymer Lubricant Designed for use in refrigeration, air conditioning, chillers, heat pumps and any hermetically sealed lubrication system, FrigiTech™ significantly reduces internal friction and heat generation, thereby prolonging equipment life as well as reducing operating costs. A specifically formulated high-tech lubricant, FrigiTech™ will give new life to bearings, seals, and all compressor parts, increase cooling capacity, quiet compressor noise, and reduce your ongoing costs of electricity. FrigiTech™ contains two anti-wear, anti-oxidation systems. The primary system stays in the solution and is triggered by temperature on an as-needed basis only. The secondary system is metal-seeking and latches onto all internal metal surfaces. This combination will therefore produce the greatest reduction at startup and maximum heat load operation, rather than in steady state power reduction. The steady state improvement in power consumption is due mostly to the secondary system creating vapor which enters the condenser containing particles of oil which create a film on the condensing surfaces, creating additional resistance to heat transfer. [top] HVAC Fluid Heat Correction Increase the performance and cooling capacity of air conditioning and refrigeration units up to 35% while adding to the life of your compressors. Air conditioning and refrigeration units that are air cooled can benefit dramatically from the use of the EASI Final Condenser™which pre-cools and sub-cools the refrigerant before entering the unit's evaporator. All air cooled systems have a condensing unit whose purpose
is to cool the hot gas coming from the compressor into a cold
liquid. This cold liquid is then sent on to the evaporator
to do the cooling. The cooler the gas is to being with, the
less heat the condenser must dissipate, and the more efficient
the system will operate. Pre-cooling dramatically improves
the condenser's ability to make the liquid colder, making
the evaporator colder, which turns off the compressor sooner,
saving you energy dollars. Additionally, sub-cooling eliminates
flash gas, further cooling the evaporator. Because there is
colder liquid and cooler gas circulating in the system, head
pressure is less and the compressor doesn't work as hard,
saving you additional energy dollars. Reduced head pressure and sub-cooling additionally create an extra cooling capacity which could possibly eliminate the need for additional or larger compressors. [top] Transient Voltage Surge Suppressor Protects sensitive, electronic equipment from voltage transients that cause continual stress and degradation of microprocessor circuitry while shortening the life of motors and lighting. The EASI TVSS™ provides an instantaneous response to voltage spikes that are greater than line voltage, dissipating the surge to ground before reaching your equipment to cause expensive performance degradation or damage. What you can't see can hurt your equipment and computers. Momentary surges in line voltage frequently occur and can exceed several thousand volts RMS. No matter how brief in duration, these surges can shorten the life of motors and lighting, plus cause severe damage to computers and other microprocessor based equipment The EASI Industrial Voltage Surge Suppressor is designed for quick and easy installation at electrical panels and safety switches, or directly at the load. Its instant response to voltage spikes and cost effectiveness of operation make it the logical choice and your first line of defense in combating transient voltage surges. [top] Power Quality Correction An advanced technology that corrects both reactive and distortion current, increasing the efficiency and lowering the costs of any facility using today's sophisticated nonlinear equipment. While improving facility power quality the PowerLiner™ dramatically decreases billed electricity costs by recycling wasted reactive and harmonic energy, producing enough savings to pay for itself 10 to 15 times during it's normal lifespan. The PowerLiner™ is both a reactive current correction system as well as a harmonic current filter. By combining both functions into a completely passive device that wires in parallel with a treated load, significant reductions in harmonic current can be reliably and safely achieved, while also gaining all the benefits and savings associated with reactive current elimination. The PowerLiner™ is an accurately tuned capacitive energy system designed especially for use in harmonics rich electrical systems. The PowerLiner™ recycles waste reactive current in the same fashion as our time proven PhaseLiner™, but permits this correction on difficult nonlinear loads...actually removing much of the 5th and 7th harmonic current in the process. By providing a local source for both reactive and distortion current, the PowerLiner™ removes this portion of your facility's electrical load, thereby causing significant reductions in heating losses throughout your entire facility's electrical system. This shows up as kilowatt hour and KW demand reductions on your electricity bill. By providing noticeable reductions in the distortion current introduced by your nonlinear equipment (any equipment that uses an AC to DC, or AC-DC-AC power supply), the PowerLiner™ reduces your costs of equipment repair and maintenance, and improves your production uptime. With the ever increasing use of AC and DC motor drives, electronic production controls, robotics, exotic welding systems, and other nonlinear loads, the PowerLiner™ is truly a tool for the new millennium. PowerLiner™ Features: · Extends the life of motors, inductive and nonlinear
equipment [top]
|
